Artemis Res Regulatory News (ARV)

Significant Intervals >0.3% Cu, 2m internal dilution. NSI = No Significant Intervals

HoleID

Comment

From (m)

To (m)

Downhole Width (m)

Cu (%)

Ni %

Co (%)

Au g/t

ARC372

14

15

1

0.57

0.38

0.020

0.01

68

72

4

0.36

0.27

0.024

0.01

Including

70

71

1

0.52

0.48

0.041

0.02

75

76

1

0.31

0.20

0.019

0.01

80

83

3

0.20

0.74

0.024

0.24

Including

80

81

1

0.74

0.24

0.024

0.02

244

245

1

0.32

0.21

0.023

0.10

ARC373

73

74

1

0.38

0.04

0.006

0.02

82

86

4

0.69

0.21

0.023

0.10

Including

83

86

3

0.82

0.24

0.027

0.12

118

119

1

0.68

0.21

0.015

0.01

125

126

1

0.50

0.33

0.032

0.02

131

132

1

1.05

0.44

0.024

0.03

ARC374

85

86

1

0.38

0.24

0.013

0.01

101

102

1

0.33

0.05

0.016

0.13

114

115

1

0.44

0.33

0.013

0.02

161

162

1

0.39

0.16

0.005

0.16

ARC375

38

40

2

0.35

0.28

0.019

0.04

45

46

1

0.34

0.20

0.015

0.02

HoleID

Comment

From (m)

To (m)

Downhole Width (m)

Cu (%)

Ni %

Co (%)

Au g/t

52

53

1

0.38

0.11

0.015

0.02

81

87

6

0.36

0.13

0.010

0.01

131

132

1

0.99

0.02

0.016

0.48

ARC376

66

67

1

0.58

0.36

0.024

0.01

76

77

1

0.44

0.24

0.012

0.04

85

87

2

0.57

0.20

0.013

0.03

90

91

1

0.31

0.13

0.010

0.01

ARC377

82

86

4

0.31

0.12

0.009

0.02

ARC382

99

100

1

0.31

0.20

0.013

0.02

101

102

1

0.30

0.17

0.010

0.01

112

114

2

0.35

0.23

0.010

0.03

ARC385

31

33

2

0.34

0.31

0.023

0.01

37

48

11

0.56

0.36

0.020

0.25

Including

40

42

2

0.70

0.69

0.032

0.04

Including

44

45

1

1.08

0.75

0.040

0.03

Including

46

47

1

0.87

0.28

0.021

0.01

ARC405

93

95

2

0.60

0.02

0.011

0.42

Including

94

95

1

0.77

0.03

0.013

0.50

ARC407

147

149

2

0.21

0.33

 -

-

Significant Intervals >0.3% Cu, 2m internal dilution. NSI = No Significant Results

Hole ID

Comment

From

To

Downhole width (m)

Cu %

Ni %

Co %

Au ppm

22CHRD001

76.46

78.36

1.9

0.30

0.16

0.013

0.02

79.93

92.5

12.57

0.43

0.25

0.018

0.08

Including

82.2

88.04

5.33

0.56

0.32

0.020

0.07

125.94

127.7

1.76

0.42

0.15

0.010

0.01

134.24

136.76

2.52

0.39

0.19

0.014

0.05

Including

135.66

136.76

1.1

0.47

0.26

0.018

0.09

HoleID

Type

East MGA

North MGA

RL (m)

Dip

Azimuth MGA

Total Depth (m)

22CHRD001

DD

507998.10

7697867.64

29.91

-60.32

212.21

174.30

ARC372

RC

507638.08

7698016.63

31.89

-60.07

212.11

342.00

ARC373

RC

507654.45

7698049.98

31.84

-60.28

214.10

339.00

ARC374

RC

508077.27

7697900.07

29.46

-60.00

210.00

342.00

ARC375

RC

508046.34

7697854.58

29.66

-60.00

210.00

342.00

ARC376

RC

508096.93

7697857.02

29.24

-59.93

212.50

254.00

ARC377

RC

508229.25

7697758.08

28.40

-59.35

212.97

162.00

ARC382

RC

507976.70

7697983.41

29.91

-59.61

212.18

342.00

ARC385

RC

507931.98

7697908.71

30.39

-61.34

208.98

342.00

ARC405

RC

507924.69

7697802.17

30.25

-59.90

129.21

162.00

ARC407

RC

508648.40

7697767.47

26.54

-69.39

210.07

210.00

Artemis Resources Limited

via Camarco

Alastair Clayton

WH Ireland Limited(Nominated Adviser and Broker)

Antonio Bossi / Megan Liddell (Corporate Finance) 

Harry Ansell / Daniel Bristowe (Corporate Broking) 

Tel: +44 20 7220 1666

Tel: +44 20 7220 1648

Camarco (Public Relations) 

Tel: +44 20 3781 9244

Gordon Poole / James Crothers

Emily Hall / Rebecca Waterworth

Email: artemis@camarco.co.uk

Sampling

techniques

· Nature and quality of sampling (eg cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc). These examples should not be taken as limiting the broad meaning of sampling.

· Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used.

· Aspects of the determination of mineralisation that are Material to the Public Report.

· In cases where 'industry standard' work has been done this would be relatively simple (eg 'reverse circulation drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay'). In other cases more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (eg submarine nodules) may warrant disclosure of detailed information.

· Reverse circulation drilling was used to obtain one metre samples, using a 5 ¼" face sampling hammer.

· Diamond sampling techniques employed at the Artemis core facility include saw cut HQ (63mm) drill core samples.

· Both RC and HQ wireline core is currently being used to drill out the geological sequences and identify zones of mineralisation that may or may not be used in any Mineral Resource estimations, mining studies or metallurgical testwork.

· Industry standard procedures were used in the case of RC whereby a one (1)m sample was collected from which a 2-3kg sample was obtained and sent to a certified laboratory to pulverize and produce a 50g charge for fire assay.

· Duplicate RC samples were collected at the rig from a static cone splitter, with the primary and duplicate bag both simultaneously collected from separate chutes.

· For RC, the cyclone was cleared between rod changes to minimise contamination.

· pXRF analysis was completed at the drill site and only used as a guide and test mineral components of a rock or alteration. No pXRF data was used in any reporting or Mineral Resource Estimations.

Drilling

techniques

· Drill type (eg core, reverse circulation, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc) and details (eg core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc).

· Reverse Circulation drilling completed by Topdrill.

· Drilling was completed using a truck mounted T685 Schramm rig mounted on 8x8 trucks

· This can produce 1000psi/2700CFM with an axillary booster which is capable of achieving dry samples at depths of around 300m.

· Diamond drilling was completed by TopDrill using a Sandvik truck mounted DE880 rig.

Drill sample

recovery

· Method of recording and assessing core and chip sample recoveries and results assessed.

· Measures taken to maximise sample recovery and ensure representative nature of the samples.

· Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.

· Recoveries are recorded on logging sheets along with encounters with water and whether the samples are dry, moist or wet.

· Drilling recoveries for Reverse Circulation drilling were >80% with some exceptions that maybe caused by loss of return through faults or encounters with water.

· >90% of samples returned dry.

· Statistical analysis shows that no bias of grade exists due to recoveries

Logging

· Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies.

· Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc) photography.

· The total length and percentage of the relevant intersections logged.

· RC samples were collected from the static cone splitter as two samples, one bulk sample and one primary (analytical) sample.

· The bulk samples are one metre splits.

· These bags are then placed in neat rows of 50 bags each clear of the rig for safety reasons.

· A field technician mixes the bag by hand before taking a sample using a sieve and sieves the sample to remove fines.

· The sieved sample is then transferred to a wet sieve in a bucket of water, and the sample is sieved further until rock fragments are clearly visible.

· These rock fragments are then logged by the site geologist, taking note of colour, grainsize, rock type, alteration if any, mineralisation if any, veining if any, structural information if notable and any other relevant information.

· This information is then written down on pre-printed logging sheets, using codes to describe the attributes of the geology.

· A representative sample is transferred to pre-labelled chip trays into the corresponding depth from where the sample was drilled from.

· The remainder of the sample from the sieve is then transferred into a core tray that has been marked up by depths at metre intervals.

· An identification sheet noting the hole number and from-to depths that correspond to each tray is then written up and placed above the tray and a photograph is taken of the chips.

· The hole is logged in its entirety, hence 100%

· The geological data would be suitable for inclusion in a Mineral Resource Estimation (MRE)

Sub-sampling

techniques and

sample

preparation

· If core, whether cut or sawn and whether quarter, half or all core taken.

· If non-core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry.

· For all sample types, the nature, quality and appropriateness of the sample preparation technique.

· Quality control procedures adopted for all sub-sampling stages to maximise representivity of samples.

· Measures taken to ensure that the sampling is representative of the in-situ material collected, including for instance results for field duplicate/second-half sampling.

· Whether sample sizes are appropriate to the grain size of the material being sampled.

· RC samples were collected on the drill rig using a cone splitter. If any mineralised samples were collected wet these were noted in the drill logs and database.

· The RC drilling rig is equipped with a rig-mounted cyclone and static cone splitter, which provided one bulk sample of approximately 20-30 kilograms, and a sub-sample of approximately 2-4 kilograms for every metre drilled.

· Field QC procedures involve the use of Certified Reference Materials (CRM's) as assay standards, along with duplicates and blank samples. The insertion rate of these was approximately 1:20.

· For RC drilling, field duplicates were taken on a routine basis at approximately 1:20 ratio using the same sampling techniques (i.e. cone splitter) and inserted into the sample run.

· Primary and duplicates results have been compared.

· The sample sizes are appropriate, representative and are considered more than adequate to ensure that there are no particle size effects relating to the grain size of the mineralisation.

Quality of assay

 data and

laboratory tests

· The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total.

· For geophysical tools, spectrometers, handheld XRF instruments, etc, the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc.

· Nature of quality control procedures adopted (eg standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (ie lack of bias) and precision have been established.

· A certified laboratory, ALS Chemex (Perth) was used for all analysis of drill samples submitted. The laboratory techniques below are for all samples submitted to ALS and are considered appropriate for the style of mineralisation defined within the Carlow Castle Project area

· The sample preparation followed industry best practice. Fire assay samples were dried, coarse crushing to ~10mm, split to 300g subsample, followed by pulverisation in an LM5 or equivalent pulverising mill to a grind size of 85% passing 75 micron.

· This fraction was split again down to a 50g charge for fire assay

· 50-gram Fire Assay (Au-AA26) with ICP finish for Au.

· All samples were dried, crushed, pulverised and split to produce a sub-sample of 50g which is digested and refluxed with hydrofluoric, nitric, hydrochloric and perchloric acid (4 acid digest).

· This digest is considered a total dissolution for most minerals

· Analytical analysis is performed using ICP-AES Finish (ME-ICP61) for Ag, Al, As, Ba, Be, Bi, Ca, Cd, Co, Cr, Cu, Fe, Ga, K, La, Mg, Mn, Mo, Na, Ni, P, Pb, S, Sb, Sc, Sr, Th, Ti, Tl, U, V, W, Zn.

· Additional Ore Grade ICP-AES Finish (ME-OG62) for Cu reporting out of range.

· Standards are matrix matched by using previous pulps from drilling programs and homogenised using certified laboratories.

· Standards were analysed by round robins to determine grade.

· Standards were routinely inserted into the sample run at 1:20.

· Laboratory standards and blank samples were inserted at regular intervals and some duplicate samples were taken for QC checks.

Verification of

sampling and

assaying

· The verification of significant intersections by either independent or alternative company personnel.

· The use of twinned holes.

· Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols.

· Discuss any adjustment to assay data.

· Sampling was undertaken by field assistants supervised by experienced geologists from Artemis Resources. Significant intercepts were checked by senior personnel who confirmed them as prospective for gold mineralisation.

· No twin holes using RC was completed in this program.

· Electronic data capture on excel spreadsheets which are then uploaded as .csv files and routinely sent to certified database management provider.

· Routine QC checks performed by Artemis senior personnel and by database management consultant.

· PDF laboratory certificates are stored on the server and are checked by the Exploration Manager.

Location of

data points

· Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys), trenches, mine workings and other locations used in Mineral Resource estimation.

· Specification of the grid system used.

· Quality and adequacy of topographic control.

· A Garmin GPSMap62 hand-held GPS was used to define the location of the initial drill hole collars. Standard practice is for the GPS to be left at the site of the collar for a period of 5 minutes to obtain a steady reading. Collar locations are considered to be accurate to within 5m.

· A high-quality downhole north-seeking multi-shot or continuous survey gyro-camera was used to determine the dip and azimuth of the hole at 30m intervals down the hole

· The topographic surface was calculated from the onsite mine survey pickups and subsequently verified by RTK GNSS collar surveys.

· Zone 50 (GDA 94).

· Surface collar coordinates are surveyed via RTK GNSS with 1cm accuracy by a professional surveying contractor.

·

Data spacing

and distribution

· Data spacing for reporting of Exploration Results.

· Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied.

· Whether sample compositing has been applied.

· In certain areas, current drill hole spacing is variable and dependent on specific geological, and geochemical targets.

· A nominal 40x20m drill spacing is considered adequate to establish the degree of geological and grade continuity appropriate for JORC (2012) classifications applied.

· No sample compositing to date has been used for drilling completed by Artemis. All results reported are the result of 1 metre downhole sample intervals.

Orientation of data in relation to geological structure

· Whether the orientation of sampling achieves unbiased sampling of possible structures and the extent to which this is known, considering the deposit type.

· If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.

· Drill holes were designed to be perpendicular to the strike of known mineralisation. Due to the structural and geological complexity of the area, mineralisation of unknown orientation can be intersected.

Sample security

· The measures taken to ensure sample security.

· The chain of custody is managed by the supervising geologist who places calico sample bags in polyweave sacks. Up to 10 calico sample bags are placed in each sack. Each sack is clearly labelled with:

o  Artemis Resources Ltd

o  Address of laboratory

o  Sample range

· Samples were delivered by Artemis personnel to the transport company in Karratha and shrink wrapped onto pallets.

· The transport company then delivers the samples directly to the laboratory.

Audits or reviews

· The results of any audits or reviews of sampling techniques and data.

· Data is validated upon up-loading into the master database. Any validation issues identified are investigated prior to reporting of results.

Mineral tenement and land tenure status

· Type, reference name/number, location and ownership including agreements or material issues with third parties such as joint ventures, partnerships, overriding royalties, native title interests, historical sites, wilderness or national park and environmental settings.

· The security of the tenure held at the time of reporting along with any known impediments to obtaining a licence to operate in the area.

· Drilling by Artemis was carried out on E47/1797 - 100% owned by Artemis Resources Ltd. This tenement forms a part of a broader tenement package that comprises the West Pilbara Project.

· This tenement is in good standing.

Exploration done by other parties

· Acknowledgment and appraisal of exploration by other parties.

· The most significant work to have been completed historically in the Carlow Castle area, including the Little Fortune and Good Luck prospects, was completed by Open Pit Mining Limited between 1985 and 1987, and subsequently Legend Mining NL between 1995 and 2008.

· Work completed by Open Pit consisted of geological mapping, geophysical surveying (IP), and RC drilling and sampling.

· Work completed by Legend Mining Ltd consisted of geological mapping and further RC drilling.

· Legend also completed an airborne ATEM survey over the project area, with follow up ground-based FLTEM surveying. Re-processing of this data was completed by Artemis and was critical in developing drill targets for the completed RC drilling.

· Compilation and assessment of historic drilling and mapping data completed by both Open Pit and Legend has indicated that this data is compares well with data collected to date by Artemis. Validation and compilation of historic data is ongoing.

· All exploration and analysis techniques conducted by both Open Pit and Legend are considered to have been appropriate for the style of deposit.

Geology

· Deposit type, geological setting and style of mineralisation.

· The Carlow Castle Co-Cu-Au prospect includes a number of mineralised shear zones, located on the northern margin of the Andover Intrusive Complex. Mineralisation is exposed in numerous workings at surface along quartz-rich shear zones. Both oxide and sulphide mineralisation are evident at surface associated with these shear zones.

· Sulphide mineralisation appears to consist of Chalcopyrite, chalcocite, cobaltite, pyrrhotite and pyrite

Drill hole Information

· A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drill holes:

· easting and northing of the drill hole collar

· elevation or RL (Reduced Level - elevation above sea level in metres) of the drill hole collar

· dip and azimuth of the hole

· down hole length and interception depth

· hole length.

· If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case.

· Drill hole information is contained within this release.

Data aggregation methods

· In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (eg cutting of high grades) and cut-off grades are usually Material and should be stated.

· Where aggregate intercepts incorporate short lengths of high grade results and longer lengths of low grade results, the procedure used for such aggregation should be stated and some typical examples of such aggregations should be shown in detail.

· The assumptions used for any reporting of metal equivalent values should be clearly stated.

· All intervals reported are composed of 1 metre down hole intervals for Reverse Circulation drilling.

· Aggregated intercepts do include reported lengths of higher-grade internal intercepts.

· No upper or lower cut-off grades have been used in reporting results.

· No metal equivalent calculations are used in this report.

Relationship between mineralisation widths and intercept lengths

· These relationships are particularly important in the reporting of Exploration Results.

· If the geometry of the mineralisation with respect to the drill hole angle is known, its nature should be reported.

· If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect (eg 'down hole length, true width not known').

· The mineralisation in the Carlow Castle Western Zone strikes generally E-W and dips to the north at approximately -75 to -80 degrees. The drill orientation was 180 -60 dip. Drilling is believed to be generally perpendicular to strike. Given the angle of the drill holes and the interpreted dip of the host rocks and mineralisation, reported intercepts approximate true width.

· True thicknesses are calculated from interpretation deriving from orientation of high-grade intervals, orientation of the main mineralised trend and its dip.

Diagrams

· Appropriate maps and sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported These should include, but not be limited to a plan view of drill hole collar locations and appropriate sectional views.

· Appropriate plans are shown in the text.

Balanced reporting

· Where comprehensive reporting of all Exploration Results is not practicable, representative reporting of both low and high grades and/or widths should be practiced to avoid misleading reporting of Exploration Results.

· This release reports the results of six RC holes out of a nine hole program. The significant results tabulated in the release are reported at a base grade of >0.5 g/t Au or >0.5% Cu. Internal dilution of up to 2 m may be included in an intersection. 

Other substantive exploration data

· Other exploration data, if meaningful and material, should be reported including (but not limited to): geological observations; geophysical survey results; geochemical survey results; bulk samples - size and method of treatment; metallurgical test results; bulk density, groundwater, geotechnical and rock characteristics; potential deleterious or contaminating substances.

· Targeting for the RC drilling completed by Artemis was based on compilation of historic exploration data, and the surface expression of the targeted mineralised shear zones and associated historic workings.

·

Further work

· The nature and scale of planned further work (eg tests for lateral extensions or depth extensions or large-scale step-out drilling).

· Diagrams clearly highlighting the areas of possible extensions, including the main geological interpretations and future drilling areas, provided this information is not commercially sensitive.

· Further work (RC and diamond drilling) is justified to locate extensions to mineralisation both at depth and along strike.