Member Info for marmaris

The ECD Equivalent circulating density in the horizontal section is the key. As you say they have to balance this going into the tubing as that will cause a back pressure and increase the ECD. I do not think that brine or water has the viscosity to lift the proppant so light mud??? I wish I knew more but I have only my thoughts to what they are doing.
They have a few options but all tricky hence the time taken and will take. Hope all is done underbalance and safely with pressure held on the well. Or they balance the well and maintain ECD only. Like managed pressured drilling. Good thing is they have continuous coil so do not have to make connections like drill pipe to maintain pressure.

Explained well. But the completion and tubing hanger will go to surface. The tree goes on top of the tubing hager. The ID of the tubing and the OD of the coil are all that matters. The casing is irrelevant here. Still tight tolerances.

Have watched it for years. Never put a penny on something I do not understand. Oil and Gold fine but that has been surreal. Just like paper gold will come to an end but will take a while.

Spot on. That will be on site for a while.

Then Bobby Ewing woke up and it was a ll a dream!!!! LOL

Mis leading there. Forgot I was retired!!! Angola 30 years ago. I asked the question with Chevron why are you running small completion tubing? In the North Sea Ninian field they were running 4/ 5 inch tubing. Angola was run by Texans and Luisianas. The north sea was operated in a different way. They looked at the rest and saw what they were doing. Then Schumberger came out with a profile computer programme to say the optimum tubing for a well depending on all the data. As in 3 inch 4 inch etc. The Texans are going way back and sticking with this old is good. That was just for you Mr Hobbs in case you think What I think you are thinking!!!!???

I was thinking of writing something similar Olderwiser BUT let the momentum continue???

Remember you can not rotate the coil from surface to bottom. like normal drilling. A motor at the end of the coil can rotate on bottom and jet the hole clean. Limited pressure due to tight tolerances though!!!

Ok. Try and keep it simple. If you have a glass of water that is 2inch across. Put something in it that is 1 inch across. Then multiply that by 10000 feet and see how much problems circulating from the bottom to the top. Remember the 1 inch is not always central in a deviated well.

Sand screens are too late. End of that conversation. Gravel pack etc too late..
Just let them clean up. Basically like drilling the well again with Ct in tubing. The well is cased and perforated. The sand will be lying on the bottom of the horizontal for 5300 feet and building up at the elbow. Without killing the well they are trying to move sand with Maybe some mud for viscosity, Everyone calm down. My old problem was completion size from Angola to USA, there was this mind set of 2 7.8 and I think this is showing here.. Chevron 20 years ago listened to me and every completion after was minimum 3,5 and ended up at 5.

I think they have 2 , 7/ 8 tubing for completion. Typical Texan **** in my opinion. North sea was minimum 3,5. So the inside diameter on the tubing is basically 2 inch. The coil will be 1 inch outside diameter . The friction losses either reverse circulating or normally are large. If they are producing gas means they know all the **** written above. Not easy to do but very ACHEIVABLE

If the flare is correct as they clean up the well the separator will have to be working and gas will be coming up the wellbore. Still good news but due to the annular velocity in small bore tubing could take a while. All good. Patience is key.

As said before I have met Scott. I have also fallen out with him. He is a very clever loon!!! Some people will get that including him. To denigrate a person like that is beyond most people. Money talks and I hope he takes all concerned to FCA and court. If the WAGS can do it why cant the FCA? Useless bunch of ******s. Now in charge of BOE and 6 months behind the curve from the beginning. QE as well.

I do not think many people on this board read the sunday times and decided to sell. This is a bear raid. The buys and sells are not far apart. The nation is.

I am right in the mood for the shorters.. Hope you are buying now. Obviously inflicting pain is your objective,
Read the RNS for a while and watch the videos. Read what Telemachus says.
For you shorters is a travel path. You wish companies to fall what a sad ****ing life.

This an attack on unfounded news. How many have sold?????? I have asked about the legality of shorting before. Some countries do not allow it. FCA and the ******s that run it really need to look again.

I am thinking they are regrouping. On platforms in North Sea they had 2 separators, Train A and B. Obviously they needed cleaned out. With the sand that is coming back from the frac if one separator have to shut in the well.. Probably need a coil tubing unit to either bail the sand from 80/ 90 degrees OR circulate it out all the way. Another separator as well so have back up. This will take time. All looks like the well will flow on its own. Need more equipment. On order and on its way. Thunderbirds are go!!!!

As said before. Pull packer. Run completion and test. That is worthy of a RNS for sure.

Hope what you read into that? Completion is not as you think. Would love to think a production packer is stab in!!! Cant be arsed anymore. You think news in one week. JOKE.

As you seem to be on the ball. Well done. I hope they have a back up xmas tree as cleaning the well up will cause abrasion even if the valves are all open. Bob And Jay are you listening!!???