Roundtable Discussion; The Future of Mineral Sands. Watch the video here.
London South East prides itself on its community spirit, and in order to keep the chat section problem free, we ask all members to follow these simple rules. In these rules, we refer to ourselves as "we", "us", "our". The user of the website is referred to as "you" and "your".
By posting on our share chat boards you are agreeing to the following:
The IP address of all posts is recorded to aid in enforcing these conditions. As a user you agree to any information you have entered being stored in a database. You agree that we have the right to remove, edit, move or close any topic or board at any time should we see fit. You agree that we have the right to remove any post without notice. You agree that we have the right to suspend your account without notice.
Please note some users may not behave properly and may post content that is misleading, untrue or offensive.
It is not possible for us to fully monitor all content all of the time but where we have actually received notice of any content that is potentially misleading, untrue, offensive, unlawful, infringes third party rights or is potentially in breach of these terms and conditions, then we will review such content, decide whether to remove it from this website and act accordingly.
Premium Members are members that have a premium subscription with London South East. You can subscribe here.
London South East does not endorse such members, and posts should not be construed as advice and represent the opinions of the authors, not those of London South East Ltd, or its affiliates.
CT5
It is you that is implying that there could be an issue, not me. You are looking for negatives in everything I say.
That Heid is not use for Fracking, it is used as a water injection pump instead of a nodding donkey or other type of pump.
The injected water will help to increase any lost pressure an move the oil in place.
So you believe the work-over rig would be required there 'after' the nodding donkey was installed, which you inferred Pboo? You tried, as usual to imply an issue.
Water injection pump
https://x.com/Heid_oil/status/1783541361603445003
CT5
The workover rig on site is a POSITIVE
But you are making it a negative with your crazy commentary 🤣 😜
I see you don't like FACTS CT5
The pump jack is in position and looks hours away from connection Pboo, but of course, the work over rig is in the picture on purpose for you to find something negative about it. Now you have, they will probably move it off site 💪
Latest pics on X show that the Nodding 🫏 is not yet connected to the well and in the background there is a workover rig.
Works in progress at the Andrews-1-17 well, Oklahoma.
"With our appetite whetted and as we learn more about the technical and production attributes of the well over the coming weeks, I am certain that our United States drilling activities will be accelerated and another positive phase of growth will be added to the Company's already successful ventures, both sides of the Atlantic." David Bramhill
Might be but they would need quite a few high pressure pumps to Hydraulic frack and lots more equipment.
That is from the permit.
Heid
I think they are using conventional perforating guns.
I dont think they are using high-pressure hydraulic fracturing.
Also researching Reach Oil an Gas wells in the Seminole county they look to me like they are pretty damm successful with only two showing as plugged an abandoned in the area ; Choat an Sullins
They are prolific in the area therefore I would be quite surprised if the Andrews well does not flow.
This is on the permits to drill at the Andrews well...
Pboo,
Have you read this ?
https://x.com/Heid_oil/status/1783473028535369960
Not sure if needs to be thrown in mix
Heid,
I have every intention to keep posting.
UJO
have not yet confirmed that the well has been perforated but I'm sure that it has.
Already to flow if it is going to.
My guess an RNS next week with results.
Worth keeping him around for comedic value but nothing more.
You know far more than most re equipment on oil sites
Please keep posting Pboo.
SuePud1
Thanks UJO for confirming it is a seperator,
Just as i said.
Https://twitter.com/UnionJackOilplc/status/1783420145915867606
Leave it out Tom dear, you should be writing an article or doing a podcast, now wasting time here picking on me xx
ChristineTaylor5 you sound more and more like TheAimCasino every day with yr indepth deep dives 😉
They are pretty standard on most wells in the US.
A pump jack is a device used in the petroleum industry to extract crude oil from a oil well where there is not high enough pressure in the well to force the oil to the surface. These pump jacks physically extract the oil for use.
Pump jacks operate by creating something known as artificial lift. This process of creating artificial lift simply increases the pressure within an oil well to pull oil to the surface. It is common for there to be insufficient pressure in the reservoir to push oil to the surface, and thus this artificial lift is used to increase production from a well. Sometimes artificial lift is required from the very beginning, whereas other times production of a well decreases over time as the pressure drops and artificial lift is needed to boost production. The beam pumping method utilized by pump jacks is the most common method for creating artificial lift.
Operation
Pump jacks operate on the same basic principle of some hand pumped water wells that some people are familiar with. Pump jacks are classified as a type of artificial lift pump system, and are the most common type of artificial lift system. This type of system uses equipment above and below ground to push oil to the surface.
These devices are composed of a long, heavy beam that is moved by some external power source. This source causes the end of the beam to rise and fall. At the end of this heavy beam are a series of rods known as sucker rods. As the beam rises and falls, the series of sucker rods dips into and out of the well. These rods are connected to a sucker rod pump, which is installed near the bottom of the well. As the system moves up and rod, the sucker rod pump works somewhat like a piston - increasing pressure within the well - and lifts the oil from the reservoir to the surface. The other end of the beam is connected to a pulley system which provides the continuous movement of the pump jack.
These pump jacks pump around twenty times a minute while extracting oil.